# How Cold a Naples Pool Gets in Winter

> NOAA normals, measured bay water temperatures and DOE guidance put numbers on how cold an unheated Naples pool gets in winter and when a heater pays off.

[Home](https://www.splashpoolsllc.com/) / [Insights](https://www.splashpoolsllc.com/blog/) / Pumps, heaters and automation Insights · Pumps, heaters and automation

# How cold does a Naples pool get in winter, and when is a heater worth running?
The first real cold front of the season arrives in Naples late in the year, and the pool goes from pleasant to untouchable. The question that follows is simple: how cold is it in there, and what would it take to fix it? Nobody publishes the temperature of a Naples pool in January, so this post builds the closest honest number from NOAA's climate normals, the nearest measured NOAA water series, the Department of Energy's own sizing method, and arithmetic you can check with a calculator.
[Clayton Waggoner](https://www.splashpoolsllc.com/about/), Owner and Managing Member, Florida license CPC1461352 · Published November 1, 2026 · 16 min read

In this article
A pool heater adds heat to the water faster than the pool loses it to the air. Two numbers decide whether it is worth running: the temperature the pool sits at without help, which tracks the air over it, and the temperature you want, which the Department of Energy puts in a typical range of 78 to 82 degrees F (U.S. Department of Energy, 2026) [7](#ref-7). Everything else is the distance between them.
The short version
I. No agency publishes a Naples pool water temperature; NOAA's Naples tide station listed no sensors and was removed on 2024-01-12 (NOAA CO-OPS, 2026) [3](#ref-3). The honest number is an estimate, built below.
II. The Department of Energy's own sizing method starts from the average air temperature of the coldest month of pool use (U.S. Department of Energy, 2026) [8](#ref-8), and NOAA's 1991 to 2020 normals put that at 65.3 degrees F for January in Naples (NOAA, 2021) [1](#ref-1).
III. The nearest measured water, the Caloosahatchee River at Fort Myers NOAA tide station, estuary water 35.8 miles north and not a pool, averaged 66.9 degrees F in January 2026 across 743 of 744 hours (NOAA CO-OPS, 2026) [2](#ref-2), within two degrees of the Naples January air normal on our comparison.
IV. On our arithmetic, a 15 by 30 foot pool with a 5 foot average depth holds 16,830 gallons at 7.48 gallons per cubic foot (USGS, 2004) [6](#ref-6) and needs 140,362 Btu per degree at 8.34 pounds per gallon (USGS, 2018) [5](#ref-5), so a 10 degree lift is 1,403,622 Btu, about 14 hours from a 100,000 Btu per hour heater with losses excluded.
V. Archived DOE guidance says heat pump pool heaters work efficiently while outside air stays above the 45 to 50 degree F range (U.S. Department of Energy, 2026) [8](#ref-8), and the Naples January normal low is 55.9 degrees F, a mean of daily lows rather than a cold-front reading (NOAA, 2021) [1](#ref-1).

I.

## How cold does a Naples pool get in winter?
Close to the month's average air temperature, with no published number more exact than that. NOAA's 1991 to 2020 normals for Naples Municipal Airport put January at a 65.3 degree F daily mean, a 55.9 normal low and a 74.8 normal high (NOAA, 2021) [1](#ref-1). The Department of Energy's sizing method treats the coldest month's average air temperature as the pool's starting point (U.S. Department of Energy, 2026) [8](#ref-8). No agency measures a Naples pool.
The frank answer is that nobody measures it. NOAA's Naples tide station, number 8725110, lists no sensors, offers no water temperature product, and was removed from service on 2024-01-12 (NOAA CO-OPS, 2026) [3](#ref-3).
What exists is the air. NOAA's climate normals are 30-year averages for 1991 to 2020, and they put the Naples January daily mean at 65.3 degrees F, December at 68.2 and February at 67.5 (NOAA, 2021) [1](#ref-1). The Department of Energy's retired sizing method treats the coldest month's average air temperature as the point the heater lifts from (U.S. Department of Energy, 2026) [8](#ref-8). An unheated pool tracks that air over days, not hours.
One measured water series nearby points the same way. The Caloosahatchee River at Fort Myers NOAA tide station, estuary water 35.8 miles north of the Naples station and not a pool, averaged 66.9 degrees F in January 2026 across 743 of 744 hours (NOAA CO-OPS, 2026) [2](#ref-2), within two degrees of the Naples January air normal on our comparison. That station's hourly low that month was 56.8 degrees F (NOAA CO-OPS, 2026) [2](#ref-2), which is what a front does to open water.

A clear Naples winter afternoon can still leave the water too cool to swim. II.

## Which months are actually cold in Naples?
Six of them, measured against the Department of Energy's comfort range. NOAA's normals put the Naples daily mean below 78 degrees F from November through April, with January lowest at 65.3 and April back up to 74.6 (NOAA, 2021) [1](#ref-1), and DOE puts typical pool water at 78 to 82 degrees F (U.S. Department of Energy, 2026) [7](#ref-7). May through October sit at or above that range without help.
The table lays out all twelve months from the same NOAA dataset, with the Fort Myers estuary water mean beside them for the ten months of 2026 recorded so far (NOAA CO-OPS, 2026) [2](#ref-2). The water column shows the shape of the year, not a pool: it is tidal river water at a gauge 35.8 miles from the Naples station (NOAA CO-OPS, 2026) [3](#ref-3).
Read down the daily mean column and the season is obvious. November's 72.4 degree F mean is already below the DOE range, December and January are the floor, and March at 70.3 is still short (NOAA, 2021) [1](#ref-1). April's 74.6 is the last month that needs help, and by May the 78.8 mean is inside the range on its own (NOAA, 2021) [1](#ref-1).
If the pool matters to you between Thanksgiving and Easter, those are the months a heater is doing real work. The [heat pump pool heater page](https://www.splashpoolsllc.com/heat-pump-pool-heater-naples/) and the [gas pool heater installation page](https://www.splashpoolsllc.com/gas-pool-heater-installation-naples/) cover what each type does in that window. The rest of this post is about how much work it is.
Naples Municipal Airport 1991 to 2020 monthly normals in degrees F (NOAA, 2021) [1], beside the 2026 monthly mean water temperature at the Caloosahatchee River at Fort Myers NOAA tide station, hourly data January through October (NOAA CO-OPS, 2026) [2]. The Fort Myers column is estuary water at a tide gauge 35.8 miles north of the Naples station (NOAA CO-OPS, 2026) [3], not a pool and not Naples.
Month Normal high (F) Normal low (F) Normal daily mean (F) Fort Myers estuary water, 2026 mean (F)
January 74.8 55.9 65.3 66.9
February 77.2 57.9 67.5 66.1
March 79.7 60.9 70.3 76.1
April 83.8 65.5 74.6 78.4
May 87.5 70.2 78.8 85.2
June 89.8 74.4 82.1 87.4
July 90.8 75.5 83.1 88.9
August 90.9 75.8 83.3 89.0
September 89.6 75.1 82.4 86.6
October 86.5 70.5 78.5 81.0
November 81.3 63.4 72.4 Not yet recorded
December 77.3 59.0 68.2 Not yet recorded

III.

## How much heat does it take to warm a pool?
One Btu per pound of water per degree F, and a pool holds a lot of pounds. The Energy Information Administration defines a Btu as the heat that raises one pound of water one degree F (U.S. Energy Information Administration, 2026) [4](#ref-4), and USGS puts a gallon of water at 8.34 pounds (USGS, 2018) [5](#ref-5). So the heat for any lift is gallons times 8.34 times degrees, our arithmetic from those two published facts.
Start with the pool's volume. Our example is a 15 by 30 foot pool, DOE's own Florida example size, 450 square feet of surface (U.S. Department of Energy, 2026) [13](#ref-13). We assume an average depth of 5 feet, a stated assumption rather than a measurement, so the shell holds 15 x 30 x 5, or 2,250 cubic feet, on our arithmetic. At 7.48 gallons per cubic foot (USGS, 2004) [6](#ref-6), that is 16,830 gallons, our arithmetic.
Now the weight. A gallon of water weighs 8.34 pounds (USGS, 2018) [5](#ref-5), so 16,830 gallons weigh 140,362 pounds on our arithmetic. The EIA's definition of a Btu is the heat that raises one pound of water one degree F (U.S. Energy Information Administration, 2026) [4](#ref-4), which means this pool needs 140,362 Btu for every degree of lift, our arithmetic from those two inputs.
A 10 degree lift, roughly the January air normal to the bottom of the DOE comfort range, is therefore 1,403,622 Btu on our arithmetic from the 8.34 pound gallon (USGS, 2004) [6](#ref-6) and the EIA Btu definition (U.S. Energy Information Administration, 2026) [4](#ref-4). For your own pool, swap in its length, width and average depth.
That figure is the heat the water must absorb, not the fuel a heater burns, because the pool keeps losing heat while it warms. Those losses are the subject of [why a pool heater stops keeping up in a Naples winter](https://www.splashpoolsllc.com/blog/why-pool-heater-not-keeping-up-naples/).
IV.

## How long does a heater take to bring the pool up?
Divide the Btu the water needs by the Btu per hour the heater delivers. Archived DOE guidance lists standard heat pump sizes of 75,000, 100,000 and 125,000 Btu (U.S. Department of Energy, 2026) [8](#ref-8) and gas outputs from 75,000 to 450,000 Btu (U.S. Department of Energy, 2026) [9](#ref-9). For our 1,403,622 Btu example, a 100,000 Btu per hour heater needs about 14 hours on our arithmetic, losses excluded.
The division is the easy part. Our example lift of 1,403,622 Btu divided by 100,000 Btu per hour is 14.0 hours on our arithmetic; at 75,000 Btu per hour it is 18.7 hours and at 125,000 it is 11.2, using the standard heat pump sizes DOE lists (U.S. Department of Energy, 2026) [8](#ref-8). A 400,000 Btu per hour gas output, near the top of DOE's range (U.S. Department of Energy, 2026) [9](#ref-9), would do it in 3.5 hours on our arithmetic. For gas, divide by the delivered output, not the input rating.
Those hours exclude losses. While the heater runs, the pool is still shedding heat through evaporation, which DOE's Better Buildings guidance calls by far the largest source of pool energy loss (U.S. Department of Energy, 2026) [7](#ref-7), so on a cold, breezy night the real heat-up runs longer than the division says.
DOE's own sizing formula handles losses differently: heater output equals pool surface area times temperature rise times 12, the rise being desired temperature minus the coldest month's average air temperature, on a basis of a 1 to 1.25 degree F rise per hour at a 3.5 mile per hour wind (U.S. Department of Energy, 2026) [8](#ref-8). For our example at 80 degrees F desired and January's 65.3 normal (NOAA, 2021) [1](#ref-1), the rise is 14.7 degrees, and 450 times 14.7 times 12 is 79,380 Btu per hour on our arithmetic from that formula (U.S. Department of Energy, 2026) [8](#ref-8).
V.

## Does a heat pump work in a Naples January?
On the normals, yes. Archived DOE guidance says heat pump pool heaters work efficiently as long as outside air stays above the 45 to 50 degree F range and lose efficiency below it (U.S. Department of Energy, 2026) [8](#ref-8). NOAA's January normal low for Naples is 55.9 degrees F (NOAA, 2021) [1](#ref-1), a mean of daily lows. A front can push a night below that, and those are the nights a heat pump slows down.
A heat pump does not make heat; it transfers heat from the outdoor air into the water (U.S. Department of Energy, 2026) [8](#ref-8). DOE's live Better Buildings fact sheet says air-source heat pumps with warm outside air are especially efficient (U.S. Department of Energy, 2026) [7](#ref-7).
The Naples normals are kind to that design. The January daily mean is 65.3 degrees F and the normal low 55.9 (NOAA, 2021) [1](#ref-1), both above the 45 to 50 degree F range DOE names as the threshold (U.S. Department of Energy, 2026) [8](#ref-8). The normal low is an average of every January night across 30 years, so single nights behind a strong front fall below it, and the heat pump's output falls with them.
Gas is the other answer. Archived DOE guidance says gas pool heaters can maintain any desired temperature regardless of weather or climate (U.S. Department of Energy, 2026) [9](#ref-9), and that heat pumps typically have much lower annual operating costs because of their higher efficiencies (U.S. Department of Energy, 2026) [8](#ref-8). The [heat pump page](https://www.splashpoolsllc.com/heat-pump-pool-heater-naples/) and the [gas heater page](https://www.splashpoolsllc.com/gas-pool-heater-installation-naples/) weigh that choice.
One rule applies to both. The City of Naples Building Department says the City does require a permit and inspection of replacement pool heaters, including gas heaters, heat pumps and solar systems (City of Naples, 2026) [12](#ref-12). Owners outside the city limits ask their own building department.

Mist off the water at dawn is heat leaving the pool into cooler air. VI.

## Does a pool cover do anything in Naples?
More than any other single step. DOE's Better Buildings guidance says evaporation is by far the largest source of pool energy loss and that covers can save 50 to 70 percent of pool heating costs (U.S. Department of Energy, 2026) [7](#ref-7). The archived Energy Saver page gives the mechanism: every pound of 80 degree F water that evaporates takes 1,048 Btu out of the pool (U.S. Department of Energy, 2026) [10](#ref-10).
The numbers explain why a cover beats a bigger heater. It takes 1 Btu to raise a pound of water 1 degree, but each pound of 80 degree F water that evaporates takes 1,048 Btu of heat out of the pool (U.S. Department of Energy, 2026) [10](#ref-10). On our arithmetic from that pair, one evaporated pound undoes the heat that lifted about a thousand pounds by a degree.
DOE says the evaporation rate rises with pool temperature and wind speed and falls with humidity (U.S. Department of Energy, 2026) [10](#ref-10). A Naples winter night is that combination: warm water, drier air than summer, and the breeze behind a front. DOE calls covering a pool when it is not in use the single most effective means of reducing pool heating costs, with savings of 50 to 70 percent possible (U.S. Department of Energy, 2026) [10](#ref-10).
There is a daytime caveat. The archived DOE page notes that outdoor pools absorb 75 to 85 percent of the solar energy striking the surface, that an opaque cover cuts that gain by 20 to 40 percent, and that in warm, humid conditions it may be more beneficial to leave the cover off during the daytime (U.S. Department of Energy, 2026) [10](#ref-10). The Naples version is cover at night, open by day. Monthly losses are in [Naples pool evaporation month by month](https://www.splashpoolsllc.com/blog/naples-pool-evaporation-rate-month-by-month/).
VII.

## When is a heater worth running, and when is it worth waiting?
Run it in the months you will swim and at the lowest temperature you enjoy. Archived DOE guidance puts the cost of each added degree at 10 to 30 percent more energy, with the higher end in warm climates (U.S. Department of Energy, 2026) [11](#ref-11). NOAA's normals say the gap to close is largest in December, January and February and closes on its own by May (NOAA, 2021) [1](#ref-1).
Desired temperature is the biggest lever you control. DOE puts typical pool water at 78 to 82 degrees F, with 78 for competitive swimming and 80 or higher for young children and older swimmers (U.S. Department of Energy, 2026) [11](#ref-11). Each degree of rise costs 10 to 30 percent more in energy, higher in warm climates (U.S. Department of Energy, 2026) [11](#ref-11). In Naples a 2 degree setpoint change is a 12.7 degree January lift against a 14.7 degree one, our arithmetic from the 65.3 normal (NOAA, 2021) [1](#ref-1).
The second lever is the calendar. The normals put the daily mean at 68.2 in December, 65.3 in January and 67.5 in February, then 70.3 in March and 74.6 in April (NOAA, 2021) [1](#ref-1). A heater set for 80 degrees F lifts roughly 12 to 15 degrees in the three cold months and about 5 in April, our arithmetic from those normals (NOAA, 2021) [1](#ref-1).
The third lever is idle time. DOE's archived advice is to turn the temperature down or the heater off whenever the pool will not be used for several days, and it calls it a myth that reheating takes more energy than the pause saves (U.S. Department of Energy, 2026) [11](#ref-11). On the normals, a pool left alone drifts back into the DOE range in May without help (NOAA, 2021) [1](#ref-1), so waiting is a real option. [Leaving a Naples pool alone for the summer](https://www.splashpoolsllc.com/blog/naples-pool-left-alone-summer-away/) covers the rest of an absence.
VIII.

## What should you tell a heater installer about your winter?
Five things: the temperature you actually want, the months you will use the pool, the surface area and average depth, whether you will cover it, and whether gas is available at the pad. Those are the inputs in DOE's own sizing method (U.S. Department of Energy, 2026) [8](#ref-8), and they decide the size and the type. The sixth is the permit the City of Naples requires for a replacement heater (City of Naples, 2026) [12](#ref-12).
Temperature and months come first, because the DOE method subtracts the coldest month's average air temperature from the temperature you want (U.S. Department of Energy, 2026) [8](#ref-8). An owner here from December starts from 65.3 degrees F; one who arrives in mid March starts from 70.3 (NOAA, 2021) [1](#ref-1) and needs a smaller rise.
Surface area is the DOE sizing input, multiplied by the rise and by 12 (U.S. Department of Energy, 2026) [8](#ref-8), so measure the pool rather than guessing. A cover habit changes the equation more than any piece of equipment, by DOE's 50 to 70 percent figure (U.S. Department of Energy, 2026) [7](#ref-7).
Gas or heat pump is the type decision: the archived DOE pages describe gas heaters as able to hold any temperature regardless of weather (U.S. Department of Energy, 2026) [9](#ref-9), and heat pumps as efficient while the air stays above the 45 to 50 degree F range (U.S. Department of Energy, 2026) [8](#ref-8). If the existing heater is the problem, start at the [pool heater repair page](https://www.splashpoolsllc.com/pool-heater-repair-naples/); the [about page](https://www.splashpoolsllc.com/about/) explains who does the work.
Ask about the permit before the heater is ordered. The City of Naples requires a permit and inspection for replacement pool heaters of every type (City of Naples, 2026) [12](#ref-12). The month for this conversation is November, with a 72.4 degree F daily mean, before the first front (NOAA, 2021) [1](#ref-1).
Ask where the unit will sit, too. Collier County, the City of Naples and Marco Island each set their own noise limits, covered in how loud a pool heat pump can be in Naples.

"Nobody measures the temperature of a Naples pool in January. The closest honest number is the air over it, and the Department of Energy's own sizing method starts from exactly that."

Ask Clayton

## Questions this article usually prompts
Tap a question. Clayton replies himself, here and on the phone.

** **[Clayton Waggoner](https://www.splashpoolsllc.com/about/)** *Owner and Managing Member · Florida license CPC1461352* Prewritten answers
Tap a question to ask

[Not covered here? Call 239-450-5933, it reaches Clayton, not a call center](tel:+1-239-450-5933)

If this is the situation you are in
[Pool heat pumps, which genuinely work in this climate &rarr;](https://www.splashpoolsllc.com/heat-pump-pool-heater-naples/)[Gas pool heater installation, sized to the whole run &rarr;](https://www.splashpoolsllc.com/gas-pool-heater-installation-naples/)[Pool heater repair in Naples, diagnosed not replaced &rarr;](https://www.splashpoolsllc.com/pool-heater-repair-naples/)[Pool automation, for a house that sits empty half the year &rarr;](https://www.splashpoolsllc.com/pool-automation-installation-naples/)
References

- [NOAA National Centers for Environmental Information, U.S. Climate Normals 1991-2020, Naples Municipal Airport (USW00012897), monthly normals data service](https://www.ncei.noaa.gov/access/services/data/v1?dataset=normals-monthly-1991-2020&stations=USW00012897&format=csv&dataTypes=MLY-TMAX-NORMAL,MLY-TMIN-NORMAL,MLY-TAVG-NORMAL,MLY-PRCP-NORMAL&includeStationName=true)
- [NOAA CO-OPS, station 8725520 Fort Myers, FL (Caloosahatchee River), water temperature data API, hourly, 2026 (monthly means are our arithmetic on the hourly series)](https://api.tidesandcurrents.noaa.gov/api/prod/datagetter?product=water_temperature&station=8725520&begin_date=20260101&end_date=20260131&units=english&time_zone=lst&format=json&interval=h)
- [NOAA CO-OPS, station 8725110 Naples, FL, station metadata (established 1965-03-04, removed 2024-01-12; no sensors; nearest station with physical sensors 8725520 Fort Myers at 35.82 miles)](https://api.tidesandcurrents.noaa.gov/mdapi/prod/webapi/stations/8725110/details.json)
- [U.S. Energy Information Administration, Glossary, British thermal unit (Btu), retrieved 1 November 2026](https://www.eia.gov/tools/glossary/index.php?id=B)
- [USGS Water Science School, A Million Gallons of Water: How Much Is It? (8.34 pounds per gallon), June 8, 2018](https://www.usgs.gov/water-science-school/science/a-million-gallons-water-how-much-it)
- [USGS Circular 1268, Estimated Use of Water in the United States in 2000, Conversion Factors (1 gallon = 8.34 pounds; 1 cubic foot = 7.48 gallons), 2004](https://pubs.usgs.gov/circ/2004/circ1268/htdocs/text-conversion.html)
- [U.S. Department of Energy, Better Buildings Alliance, Fact Sheet: Pool Efficiency (PDF), retrieved 1 November 2026](https://betterbuildingssolutioncenter.energy.gov/sites/default/files/attachments/Pool%20efficiency_.pdf)
- [U.S. Department of Energy, Energy Saver, Heat Pump Swimming Pool Heaters (page retired June 2026, Internet Archive capture 2026-01-01)](https://web.archive.org/web/20260101022502id_/https://www.energy.gov/energysaver/heat-pump-swimming-pool-heaters)
- [U.S. Department of Energy, Energy Saver, Gas Pool Heaters (page retired June 2026, Internet Archive capture 2026-05-01)](https://web.archive.org/web/20260501012216id_/https://www.energy.gov/energysaver/gas-pool-heaters)
- [U.S. Department of Energy, Energy Saver, Swimming Pool Covers (page retired June 2026, Internet Archive capture 2026-01-01)](https://web.archive.org/web/20260101014018id_/https://www.energy.gov/energysaver/swimming-pool-covers)
- [U.S. Department of Energy, Energy Saver, Managing Swimming Pool Temperature for Energy Efficiency (page retired June 2026, Internet Archive capture 2026-01-01)](https://web.archive.org/web/20260101020106id_/https://www.energy.gov/energysaver/managing-swimming-pool-temperature-energy-efficiency)
- [City of Naples Building Department, Frequently Asked Questions: "Do pool heaters require a permit?", retrieved 1 November 2026](https://www.naplesgov.com/building/page/frequently-asked-questions-building)
- [U.S. Department of Energy, Energy Saver, Solar Swimming Pool Heaters (page retired June 2026, Internet Archive capture 2026-01-01), cited only for the 15-by-30-foot Florida example pool](https://web.archive.org/web/20260101014622id_/https://www.energy.gov/energysaver/solar-swimming-pool-heaters)
[All articles &rarr;](https://www.splashpoolsllc.com/blog/)

## The article is general. Your pool is specific.

Tell us what the pool is doing, a sentence or two is enough. The person who wrote this is
the person who calls back.

[Call 239-450-5933](tel:+1-239-450-5933) [Book a consultation](https://www.splashpoolsllc.com/booking/)
