# Should You Add a Sun Shelf to a Naples Pool Remodel?

> The depth everyone quotes for a sun shelf is not a standard. Here is what Florida code actually says, and what a shelf takes from your pool and your deck.

[Home](https://www.splashpoolsllc.com/) / [Insights](https://www.splashpoolsllc.com/blog/) / Finishes, tile and stone Insights · Finishes, tile and stone

# Should you add a sun shelf to a Naples pool remodel?
A sun shelf is the most requested addition on a remodel and the least examined. The pitch is easy, because a shallow ledge you can put a chair on is genuinely pleasant in Southwest Florida. What almost nobody explains is that a shelf is not added to a pool so much as taken out of one, that the depth figure repeated across every page selling them is not a rule, and that in Collier County the decision touches your stormwater paperwork. None of that makes a shelf a bad idea. It makes it a decision worth understanding first.
**Clayton Waggoner**, Owner and Managing Member · Published August 26, 2026 · 15 min read

In this article
A sun shelf, also called a tanning ledge, is a broad shallow platform inside the pool, deep enough to sit in and shallow enough to stay warm. In Florida there is no residential code number defining one. The only published dimensional rule naming a sun shelf is in the public pool section of the building code, which requires that where a step or shelf protrudes into the pool, the remaining width to the opposite wall be 10 feet or more (Florida Building Code, 2023) [2](#ref-2). That section governs public pools and states that the term does not include a swimming pool located on the grounds of a private residence (Florida Building Code, 2023) [1](#ref-1).
The short version
I. There is no residential standard for sun shelf depth in Florida. The depth range repeated on nearly every page selling them is an industry convention, not a code requirement, and no page we found says so.
II. The one Florida rule that names a sun shelf is in the public pool chapter. It requires 10 feet of remaining width from the shelf riser to the opposite wall (Florida Building Code, 2023) [2](#ref-2), and by its own definition that chapter does not include a swimming pool located on the grounds of a private residence (Florida Building Code, 2023) [1](#ref-1).
III. A shelf is subtracted from swimming area, not added to the pool. On a typical Naples backyard pool the shelf comes out of the shallow end, which is the part people actually stand in.
IV. More surface area means more evaporation, every day, forever. South Florida runs about 0.095 inches a day in December to about 0.184 inches a day in May (SFWMD, 2010) [3](#ref-3), and that rate applies to the shelf as much as to the rest of the pool.
V. In Collier County the deck side of the decision can reach your paperwork. New impervious area is what triggers the stormwater plan requirement under the Land Development Code (Collier County LDC, 2017) [4](#ref-4).

I.

## What does Florida code actually say about a sun shelf?
Almost nothing, for a backyard pool. The only Florida rule naming a sun shelf sits in the public pool section, which requires 10 feet of remaining width from the shelf riser to the opposite wall (Florida Building Code, 2023) [2](#ref-2). That same section defines its scope and excludes private residences by name (Florida Building Code, 2023) [1](#ref-1).
This is worth stating plainly because the internet implies otherwise. Search the question and you will find depth figures presented with the confidence of a code citation, usually without a citation.
Here is what exists. Florida Building Code section 454.1 covers public swimming pools and bathing places, and its definition of a public pool ends with a sentence that decides this whole question: the term does not include a swimming pool located on the grounds of a private residence (Florida Building Code, 2023) [1](#ref-1). Residential pools fall under a different section.
Inside that public pool section is the only rule we found anywhere in Florida code that names the feature. Where interior steps or a sun shelf protrude into the pool, the remaining width from the junction of the step or shelf riser and the floor to the opposite wall shall be 10 feet or more (Florida Building Code, 2023) [2](#ref-2).
We are quoting that as the best published statement of practice available, not as a rule that binds your backyard. It is not one. But it is a real dimension written by people thinking about the same geometry problem, and a homeowner deciding how much pool to give up is entitled to know it exists.
The practical reading: if your pool is narrow, a shelf protruding into it will leave less open water than a public facility would be permitted to leave. That is allowed at a private residence. Whether you will enjoy it is a different question, and it is the one to ask before the shell is cut.
II.

## Why is there no standard depth for a residential sun shelf?
Because no residential standard defines the feature at all. What you find instead is a convention, repeated widely enough that it reads like a specification. The depth that actually works is decided by what you intend to put on the shelf and how the shelf drains, not by a number.
We are deliberately not publishing a depth range here, and the reason is the same one that governs the rest of this site. A number with no source behind it becomes a specification the moment it appears on a page, and this trade is already full of figures that survive because they were repeated rather than because they were measured.
What decides the depth in practice is furniture. A shelf sized for a lounger with short legs is not the same as one sized for a chair you want water halfway up, and neither is the same as one intended mainly for small children under supervision. Those are different depths and the difference is inches.
The second input is drainage and circulation. A broad shallow platform is the part of the pool most likely to go stagnant and stain, because it holds the least water, warms the fastest and sits furthest from the returns. How the shelf is plumbed matters more than the depth number and is asked about far less.
The third is the finish. Shallow water over a light finish shows every deposit, and a shelf is precisely where sunscreen, leaves and mineral staining collect. We covered why staining is usually not what people assume in [pool staining in Southwest Florida](https://www.splashpoolsllc.com/blog/pool-staining-southwest-florida-not-your-water/).
So the honest answer to how deep it should be is that it depends on what it is for, and any contractor who answers with a single number before asking what you plan to put on it is quoting a habit.
III.

## Does a sun shelf make the pool smaller?
Yes, and this is the part the renderings hide. A shelf is carved out of the pool's footprint rather than added to it, and on most Naples backyards it comes out of the shallow end. The water you lose is the water people actually stand in.
Look at a plan view rather than a photograph. The shelf occupies a rectangle or a curve at one end, and every square foot of it was previously swimmable water. On a large pool that is a rounding error. On the more common Naples backyard pool it is not.
The specific loss matters more than the total. A shelf almost always takes the shallow end, because that is where the depth already suits it and where the structure makes it straightforward. The shallow end is also where people stand, where children play and where anyone doing anything other than swimming laps spends their time.
That is the trade to weigh honestly: you are converting the most used part of the pool into the most photographed part. For plenty of households that is the right call. For a family who use the shallow end constantly, it frequently is not, and nobody tells them before the drawing is approved.
The geometry rule quoted above is a useful reference point even though it does not bind you. If a public facility would have to leave 10 feet of open width past the shelf riser (Florida Building Code, 2023) [2](#ref-2), and your pool would leave considerably less, that is worth seeing on paper before it is concrete.
Ask for the plan view with the shelf drawn to scale and the remaining open water dimensioned. It is a reasonable request, it costs nothing, and it makes the trade visible.
IV.

## What does a sun shelf do to evaporation and water loss?
It increases both, permanently, because evaporation is driven by surface area. South Florida runs about 0.095 inches a day in December to about 0.184 inches a day in May (SFWMD, 2010) [3](#ref-3), and a shelf adds surface at the warmest, shallowest part of the pool.
Evaporation is not a fixed number of gallons per pool. It is a depth of water lost per unit of surface per day, which means a wider pool loses more than a narrow one at the same rate. Adding a shelf widens the water surface.
The modeled band for this region runs from about 0.095 inches a day in December to about 0.184 inches a day in May (SFWMD, 2010) [3](#ref-3). We published that band to replace the quarter inch a day figure this trade repeats without a source, and the full month by month picture is in [Naples pool evaporation, month by month](https://www.splashpoolsllc.com/blog/naples-pool-evaporation-rate-month-by-month/).
A shelf compounds it slightly beyond the raw area, because shallow water sitting in full sun runs warmer than the body of the pool, and warmer water evaporates faster. That is a modest effect rather than a dramatic one, and we are not going to attach a figure to it that we have not measured.
The reason to care is diagnostic rather than financial. If you add a shelf and your top-up frequency rises, that is expected physics and not a leak, and knowing the difference saves an unnecessary call. If the rise is far larger than the added area explains, that is worth investigating properly with [leak detection](https://www.splashpoolsllc.com/pool-leak-detection-naples/).
The same logic runs the other way for heating. More surface at shallow depth means the shelf gains heat quickly in the afternoon and gives it back quickly overnight.
V.

## Can a sun shelf be added to a pool that already exists?
Sometimes, and it is a structural job rather than a finish job. Adding a shelf to an existing pool means cutting into a shell that was engineered without it, which is a different proposition from forming one when the pool is built.
This is the question we are asked most often on a remodel and the one with the least honest answer available online, because the answer is frequently no, or not the way you are imagining.
An existing pool shell is a structure. Its walls, floor and bond beam were built as a system, and a shelf is not a decoration laid on top of that system, it is a modification of it. Cutting a shelf into an existing wall means removing part of the wall and building a new structural element that ties back into the remaining shell properly.
Done correctly that is real construction, and it is the point where the answer stops being about whether you want a shelf and starts being about what the shell will accept. Done incorrectly it is the origin of a crack that will keep coming back through every finish applied afterward, which is a failure mode we described in [telling a structural crack from a cosmetic one](https://www.splashpoolsllc.com/blog/pool-crack-structural-or-cosmetic-naples/).
There is a common middle path worth knowing about. Where the existing shallow end is already broad and the geometry cooperates, a shelf can sometimes be formed by building up rather than cutting out, raising a section of floor instead of removing part of a wall. That is a smaller structural intervention. It is also not always possible, and whether it is depends on the pool in front of us rather than on a general rule.
Either way, this is settled by looking at the pool. Anyone willing to tell you over the phone that a shelf can be retrofitted has not seen the shell.
VI.

## Does adding a sun shelf change your stormwater paperwork in Collier County?
The shelf itself is water rather than impervious surface, but a shelf project rarely arrives alone. It is the deck that usually grows with it, and new impervious area is what triggers the stormwater plan requirement under the Collier County Land Development Code (Collier County LDC, 2017) [4](#ref-4).
This is the connection almost nobody makes, and it catches people at plan review rather than at the design table.
A sun shelf is normally paired with something on the deck side, because a shelf you cannot reach comfortably is a shelf you do not use. Where the shelf is being won back from a deep end rather than added at the edge, that is the work described in [making a Naples pool shallower](https://www.splashpoolsllc.com/blog/make-a-pool-shallower-naples-remodel/). Wider coping, a landing, a widened deck for chairs, sometimes a new walkway around the end of the pool. Each of those is deck area rather than water.
New impervious area is the trigger that matters. The Collier County Land Development Code sets out when a stormwater plan is required for a single family dwelling (Collier County LDC, 2017) [4](#ref-4), and the threshold is measured on new impervious area rather than on what kind of project you called it. We worked through how the county treats a paver deck, and why the layer underneath changes the answer, in [paver pool decks and impervious area](https://www.splashpoolsllc.com/blog/paver-pool-deck-impervious-area-collier-county/).
The sequencing lesson is simple. Decide the deck at the same time as the shelf, not after it. A shelf approved on its own, followed six weeks later by the deck widening that makes it usable, is the version of this that generates a second trip through review.
If your property is outside Collier County, none of the above governs your job. Bonita Springs and Estero are in Lee County with their own permitting authorities, which we flag on those pages rather than letting the Collier material be assumed to transfer.
VII.

## What should you settle before anyone breaks ground?
Four things: what the shelf is actually for, what it takes from the swimming area, how it will be plumbed, and whether the deck changes with it. Settling those before drawings turns a shelf from an impulse into a design decision.
Start with use, because it decides depth and nobody asks. A shelf for loungers, a shelf for sitting waist deep and a shelf mainly for supervised toddlers are three different depths, and the honest way to arrive at yours is to name the furniture rather than accept a range.
Second, ask for the plan view with the remaining open water dimensioned. You are giving up swimmable area, almost certainly at the shallow end, and that trade is invisible in a rendering and obvious in plan.
Third, ask specifically how the shelf will be circulated. A broad shallow platform is the most likely part of the pool to stagnate, warm and stain, and returns positioned for the old shape will not necessarily serve the new one. This is a plumbing conversation and it belongs before the shell work, not after.
Fourth, decide the deck at the same time. If the usable version of this shelf needs a wider landing, that is new impervious area and it belongs in the same submission (Collier County LDC, 2017) [4](#ref-4).
And if the shelf is going into an existing pool, get the structural answer first. Whether the shell will take it is not a preference question, and it is the one that decides whether the rest of the conversation is worth having. That is a site visit, not a phone call, and it is the same visit that would tell us whether the pool needs [resurfacing](https://www.splashpoolsllc.com/pool-resurfacing-naples/) anyway.

"A sun shelf is not added to a pool. It is taken out of one, usually out of the shallow end, which is the part of the pool people actually stand in."

Ask Clayton

## Questions this article usually prompts
Tap a question. Clayton replies himself, here and on the phone.

** **Clayton Waggoner** *Owner and Managing Member · Splash Pools* Online
Tap a question to ask

[Not covered here? Call 239-450-5933, it reaches Clayton, not a call center](tel:+1-239-450-5933)

If this is the situation you are in
[Pool remodeling in Naples, handled as one project →](https://www.splashpoolsllc.com/pool-remodeling-naples/)[Pool resurfacing in Naples, including the part everyone skips →](https://www.splashpoolsllc.com/pool-resurfacing-naples/)[Pool deck pavers in Naples, built on a base that lasts →](https://www.splashpoolsllc.com/pool-decks-pavers-naples/)[Pool deck repair in Naples, and whether resetting will actually hold →](https://www.splashpoolsllc.com/pool-deck-repair-naples/)
References

- [Florida Building Code 2023, 8th Edition, Section 454.1: Public Swimming Pools and Bathing Places (scope and definitions)](https://up.codes/s/public-swimming-pools-and-bathing-places)
- [Florida Building Code 2023, 8th Edition, Section 454.1.2.2.2: Walls and Corners (remaining width where a step or sun shelf protrudes)](https://up.codes/s/swimming-pool-construction-standards)
- [South Florida Water Management District, Technical Paper 107, Pan Evaporation and Potential Evapotranspiration Trends in South Florida (Abtew, Obeysekera and Iricanin, 2010)](https://www.sfwmd.gov/sites/default/files/documents/tech_paper_sfer_107_r.pdf)
- [Collier County Land Development Code, section 6.05.03, Stormwater Plans for Single-Family Dwelling Units, Two-Family Dwelling Units, and Duplexes (Ord. No. 17-12, section 3.B)](https://library.municode.com/fl/collier_county/codes/land_development_code)
[All articles →](https://www.splashpoolsllc.com/blog/)

## The article is general. Your pool is specific.

Tell us what the pool is doing, a sentence or two is enough. The person who wrote this is
the person who calls back.

[Call 239-450-5933](tel:+1-239-450-5933) [Book a consultation](https://www.splashpoolsllc.com/booking/)